All-in-one Solistek A1+ 1000w Complete De Light System 120/240v (controller Ready) Perfect Gift [mGy4ozaN]

The SolisTek A1+ 1000 watt, DE (Double Ended) complete fixture is a professional high output light with the highest performance on the market based on reliability, output, & consistency. Safety and technology are the foundation of all SolisTek products. This SolisTek commercial lighting fixture is equipped with many features that are SolisTek exclusive and designed in a way that is simple & easy to use.

The SolisTek A1+ powers both double ended HPS & Metal Halide lamps. SolisTek DE HPS lamps have proven to have incredibly high PAR output, a broader spectrum than traditional single-ended HPS lamps, and only 5% depreciation @ 10,000 hours.  SolisTek Metal Halide lamps have proven to be a great solution for providing mixed spectrum to your garden.

Designed around the competition, the SolisTek A1+ provides high output & consistent uniform spread. This fixture is the preferred choice among growers who understand light quality.

Features:

• Professional 1000W adjustable ultra high-frequency lighting system
• High efficiency super reflective horticultural aluminum
• Suitable for High-Pressure Sodium & Metal Halide Lamps
• Incredibly high output & even spread
• Featuring Ignition Control™ & SenseSmart™ diagnostic check
• Includes SolisTek high output 2,100 µmol HPS lamp
• Lightweight & easy to install & reflector is easily replaceable

 Ignition Control™, SenseSmart™, Soft Start technology are standard in all Solis Tek Digital Ballasts.

What is SenseSmart?

SolisTek SenseSmart checks for 8 different factors using Pre-ignition self-diagnostic checks before attempting to power the lamp; this is intended for increased user safety.

SenseSmart check for:

• Open Output
• High/Low Temps
• Ignition Failure
• Thermal
• End of Lamp Life
• Overflow Current
• Over/Low Voltage
• Short Circuit

SolisTek digital ballasts complete a closed circuit between the lamp and power source.  If any sort of break or inconsistency has been detected, it will not strike the lamp.  The ballast will detect if the lamp is too hot to ignite, lamp compatibility issues, if there is no lamp plugged in, or if a lamp is defective or about to fail it will detect that it is not receiving enough of a signal coming back.  It can even detect if there’s a short on your wiring, reflector, lighting controller, or a defective breaker on an electrical panel.

This is all apart of  SolisTek's exclusive SenseSmart safety mechanism that was introduced in 2010.  If it detects any sort of anomalies or disturbances it will turn off the lamp and attempt to re-strike every 90 seconds until it deems that it is safe to ignite.  99% of the time an error code is displayed (Matrix) or if the green led (standard unit) stays on without the lamp igniting it is pointing to something on the users end to troubleshoot.  In the rare instance that a component goes out the ballast will disable itself to prevent anything further from happening.

What is Ignition Control?

Aside from the industry’s lowest output Total Harmonic Distortion (THD%), SolisTek ballasts also offer the industry’s only true Ignition Control staggered ignition technology.

SolisTek’s sequential lamp ignition technology will ignite your lamps one at a time based on load stability.  This revolutionary technology (not a randomized startup) will actually detect the voltage and amperage frequencies of the electrical circuit and fire lamps when the load is most stable.  Prevent surges and spikes in your electrical environment and stop overloading breakers. When you power multiple SolisTek ballasts, the electrical draw is controlled by the internal software, maximizing electrical efficiency. 

SolisTek digital ballasts are the only ballast capable of this technology.

Specs

• Footprints (dependent on crop & DLI)
• Warehouse Coverage:
• Single unit: up to 6′ x 7′
• Series: 5′ x 6′
• Greenhouse Coverage (Primary):
• Single unit: up to 7′ x 8′
• Series: 6′ x 7′
• Greenhouse Coverage (Supplemental):
• Single unit: up to 8′ x 10′
• Series: 7′ x 8′
• Dimensions: 30" x 17" x 9"
• Weight: 23 lbs

Calculators

• Room Calculator - Number of lights based upon room size and layout
• Heat Conversion - BTU's and AC Requirements

• Amperage Calculator

Instructions

SolisTek Digital Lighting

PLEASE READ INSTRUCTIONS BEFORE INSTALLATION

Congratulations on your purchase of the industry’s highest quality digital lighting products. SolisTek digital ballasts are tuned and optimized for the lowest OUTPUT total harmonic distortion (THD) and matched to SolisTek Digital Lamps for maximum output and spectral balance.

Incorrect use or installation may lead to product damage or failure. Any damage caused by incorrect use or installation voids the manufacturer’s warranty. Please carefully read this manual before installing your digital ballast.

Unique Technology

• Ignition Control™: SolisTek’s Ignition Control is a software-based technology that allows one‐at‐a‐time sequential lamp ignition. No matter how many SolisTek ballasts you are running, your lights will ignite one‐at‐a‐time. By utilizing a staggered ignition, SolisTek ballasts prevent huge current draws/spikes in your electrical system and is a more efficient means of lighting your garden.
• SenseSmart™ Technology: When the ballast is powered on, SolisTek ballasts will send a mV signal through the closed circuit (between ballast and lamp), to determine a variety of different factors such as: lamp type, open/short circuits, high/low temps and thermal issues, ignition failure, overflow current, and end of lamp life.
• World’s Lowest HID OUTPUT THD%: With an input Total Harmonic Distortion (THD) value of <10% and an output THD% of <12%, SolisTek digital ballasts provide the cleanest signal for HID lamps. This provides maximum output, spectral perfection, and longevity of your equipment.

Installation

SolisTek digital ballasts can be positioned universally. The unique design of the heat sink dissipates heat away from the critical components in the ballast. If ballasts are mounted vertically to a wall, it is preferred to mount lamp output side TOP and mains BOTTOM. SolisTek digital ballasts are designed for use indoors and are sealed for damage against humidity and dust.

Avoid installing your ballasts in a high heat area, such as an attic or closed area or rooms that reach temperatures over 100°F. Do not stack ballasts on top of another. When placing ballasts, make sure to keep a distance of at least approx. 6” in between individual ballasts. Do not install in a wet area or areas prone to water.

SolisTek digital ballasts, depending on model, are compatible both on 120V and 240V power and are also generator ready. When installing your ballasts, we recommend to utilize up to 80% maximum load of your breaker capacity for electrical safety. 

CONTACT A LOCAL ELECTRICIAN IF YOU HAVE ANY DOUBTS.

Lamp Connections

• Never turn on the ballast without the lamp cord and lamp installed.
• Never disconnect the lamp from a live ballast.
• Hot‐restrike: it is very important to allow your lamp to cool before attempting to reignite. It is recommended to allow 20‐30 minutes before restarting to avoid damage to the lamp.
• Ensure a snug fit when installing lamps
• Make sure the mogul socket shows no signs of damage or corrosion.
• Confirm that power has been disconnected from the ballast before attempting to change lamps. 

Compatible Lamps

SolisTek digital ballasts operate both Metal Halide (MH) and High Pressure Sodium (HPS) lamps. While SolisTek digital ballasts are compatible with a majority of brand name lamps, SolisTek digital lamps are recommended. Our technical engineer’s tune and match our light systems together for optimal output and spectral balance. Using a matched SolisTek system has significant benefits over unmatched systems in terms of light quality and longevity.

• 1000W Ballast, recommended to use 1000W lamps only, or run 2 x 600W with the SolisTek splitter.
• 600W Ballast, recommended to use 600W or 400W lamps.
• Please make sure the proper wattage lamp is installed before adjusting ballast to full power or boost mode.
• SolisTek digital ballasts have soft‐start integration, ballasts ease up to full draw.
• SolisTek ballasts utilize soft‐dimming, power will ease up to full draw. It may take a few minutes for the ballast to dim from each setting. Visible dimming may not be noticeable to the human eye.

Preventing EMI

All high frequency ballasts, to a degree, will cause electromagnetic interference (EMI). Incorrect installations may cause unnecessary EMI.

• If possible, install ballasts as far away from major communication sources.
• Do not coil your excess lamp cords or wiring. Shorten lamp cords and wires to the required lengths.
• Keep mains leads (power cords) and lamp leads separate.
• Maintain integrity of electrical system
• EMI may be more prevalent in areas with older grid systems.

Maintenance

SolisTek digital ballasts are not self‐serviceable. If you experience a need for assistance, please call our information line. Disassembling the ballast will void the warranty. The internal componentry of the ballast is sealed with a resin to protect electronics. The aluminum exterior of the ballast can be cleaned with a damp cloth, however, make sure the ballast is disconnected before cleaning.

It is recommended to check all connections regularly to make sure that no cables have become loose or show signs of damage. Also, check to confirm all wire ends are fitted firmly into the reflector/ballast.

Troubleshooting

If the HID lamp will not start, the possible causes and fixes are below:

Possible Causes:

• Lamp is loose in socket
• Incorrect voltage
• Defective or poor wiring
• Poor electrical connections
• Incorrect or damaged lamp
• Breaker reset required

Possible Fixes or Corrective Maintenance:

• Make sure lamp is screwed firmly into the socket, but do not over tighten. Ensure the tab inside the mogul socket makes proper contact with the lamp base.
• Make sure you are using the correct voltage input.
• Examine wiring to confirm proper connections.
• Verify that you are using the proper voltage lamp, use SolisTek digital lamps for best results.
• Check to make sure there is no lamp damage, sometimes lamps are installed too firmly, look for broken connections.

Manufacturer Warranty

LIMITED LIFETIME WARRANTY POLICY 

Solis Tek warrants its digital ballast and complete fixtures to be free from defects in materials and workmanship if used under normal operating conditions for a period of (3) years from original customer’s date of purchase.

Solis Tek warrants its lamps and accessories to be free from defects in materials and workmanship if used under normal operating conditions for a period of (1) year from the original customer’s date of purchase.

Not Covered Under Warranty:

• Damage due to mishandling or abuse of the product.
• Not using a voltage regulated power supply to connect products or controls.
• Connecting units to the wrong output voltage.
• Improper connection of power supplies, products or controls.
• Connection of products or controls directly to any A/C power source.
• Connecting power supplies backward to an A/C power source.
• Water damage to non-waterproof products.
• Electrical power surges.  Note: It is recommended that if there is a possibility of power surges then you should consider a surge protector for the incoming A/C power line.
• Damage from lighting or electrical storms.
• Natural Disasters (example: hail, flooding, tornado, fire, and wind).
• Products or electronic components that have been modified by the user.
• Products used for purposes other than intended and directed.

Products damaged by connection to systems or components not purchased from Solis Tek Inc.

COMPANY WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE GOODS OR OTHER INDIRECT DAMAGES WITH RESPECT TO LOSS OF PROPERTY, REVENUES, LIFE OR LIMB, PERSONAL INJURY AND CLAIMANTS REMEDIES SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF NON-CONFORMING GOODS.