Festive Deal Bmw E36 328i/m3 1996-1999, E36/7 Z3/z3m 1997-2000 Ms3pro Pnp Plug And Play Ecu Limited Time 75% Off [SKkJqr09]

Replace your “Siemens MS41” DME with a tunable racing ECU! MS3Pro Plug and Play for 1996-1999 BMW M3 E36 and 1997-2000 BMW Z3M allows tuning your E36/7 with a laptop to handle any mods you can throw at these engines!

MS3Pro Plug and Play for 1996-1999 BMW M3 E36 fits the following applications. Confirmed for US market vehicles:

• 1996-1999 BMW E36 328i with M52 motor and manual transmission
• 1996-1999 BMW E36 M3 with S52 motor and manual transmission
• 1995-1998 BMW E39 528i with M52 motor and manual transmission
• 1995-1998 BMW E38 728i with M52 motor and manual transmission
• 1997-1998 BMW Z3 2.8i with M52 motor and manual transmission (Not compatible with the later M52TU motor)
• 1997-2000 BMW Z3M with S52 motor and manual transmission

**European market M3 compatibility is not confirmed at this point.                      **South African market 1997-2000 Land Rover Defender with M52 likely to work, but compatibility is not confirmed at this point.

MS3Pro Plug and Play for 1996-1999 BMW M3 E36 Model Features:

• Fully Plug and Play Installation – No wiring required for basic functionality.
• The ONLY aftermarket M52 ECU on the market that supports the stock BMW camshaft position sensor – NO Hall sensor retrofit needed!!!
• Maintains functionality of the factory ACS+T traction control system
• Maintains functionality of the factory Econometer/MPG gauge on the dashboard
• Base map is pre-loaded to help your engine start on the first turn of the key
• Real time tuning and data logging with a laptop connection
• 8 GB internal data logging with built in SD card
• Supports most aftermarket wideband sensors

Fully Tunable Engine Control!

• 16×16 Fuel Tables allow high resolution tuning
• 16×16 Ignition Tables
• Multiple Acceleration enrichment strategies
• Closed Loop Idle Speed Control
• Air Conditioner Control
• 6 sequential fuel injector channels with individual trim tables
• Onboard high impedance injector drivers
• Allows removal of stock MAF sensor
• VANOS control

Advanced Feature Set (Included!)

• 12×12 Air Fuel Ratio Target Tables for use with wide band O2 sensor for precise tuning and table trim.
• Multiple traction control strategies
• Built-in 3-step rev limiter / launch control with flat shift and burnout rev limiter
• Time based timing / boost increase after launch
• Real time barometric correction
• Internal 4-bar MAP sensor reads up to 44PSI of boost
• Overboost protection
• Closed loop boost control (Requires DIYAutoTune.com EBC solenoid kit)
• CO2 based boost control
• Set boost by RPM and throttle, ground speed, or gear
• Rally style anti lag
• Water injection control – on/off or variable
• Knock sensor input with adjustable sensitivity, crank angle windowing, and more
• Table switching input. Change fuel and spark maps on the fly for different fuels, nitrous activation, etc.
• Input for flex fuel sensor – switch between E85 and gasoline on the fly!
• CANBus connector allows interconnection of other MegaSquirt-compatible devices for additional functions (EGT Input, Automatic Transmission Controller, Additional Sensors…..the possibilities are limitless!

What you get in the box:

• MS3Pro Plug and Play for 1996-1999 BMW M3 E36 ECU
• RS232 tuning cable
• 20 Pin Options Connector
• Tuning Software and Documentation on USB memory stick with two base maps included:
  • Stock M52
  • Stock S52
• 6′ Vacuum Hose for MAP Signal and ‘T’ fitting
• ECU mounting brackets
• Registered version of TunerStudio and MegaLog viewer included

Direct replacement for:

• Siemens MS41.x DME

Not compatible with:

• M52TU DME Siemens MS42

If your ECU / DME has a different part number, please contact us to see if it is compatible with MS3Pro Plug and Play for 1996-1999 BMW M3 E36 & 1997-2000 BMW Z3M.